![]() | |
| |||||||
| Notices |
| Wide boys Previa, Wide Estima and Estima based Tarago technical chat |
![]() |
| | LinkBack | Thread Tools | Display Modes |
| | #1 | ||||||||
![]() Join Date: May 2008 Location: Fleetwood,Lancs Thanks: 0
Thanked 0 Times in 0 Posts
![]()
| Hi all! Does anyone know if it is possible to fit captains seats in place of the driver / front passenger seats in a '94 Previa 2.4 Auto please? If so, which seats would you recommend? I know that access to the engine has to be retained and this could make things a bit awkward. Also,can the middle bench seat be replace with swivelling seats and would seats from a Lucida/Emina fit? I'm wanting to use the bus as an occasional weekend camper and the swivelling seats would be a big help. I'm planning to remove the rear seats in favour of a removeable hob/grill/sink unit. If anyone has done a similar conversion I would love to hear from you - any help / ideas would be greatly appreciated. Many thanks, Greg. | ||||||||
| | |
| Sponsored Links |
| | #2 | |||||||||
![]() Join Date: May 2008 Location: Texas, USA Thanks: 0
Thanked 0 Times in 0 Posts
![]()
| Quote:
as for the middle row, I'm sure the floorpan is the same on all of the previas, it's just the seat retaining hooks will obviously be different as well as holes in the carpet... I would pull back the carpet to make sure before attempting the swap though | |||||||||
| | |
| | #3 | ||||||||
![]() Join Date: Dec 2007 Thanks: 0
Thanked 1 Time in 1 Post
![]()
| I don't know about the Previa - but I do know that the Estima has a different floor pan between the 7 and 8 seater ( different rear axle setup as well) and the middle row seats are not interchangeable. Seems the 7 seater is the higher spec and a different floor pan is required for the independent rear axle and captains seats. So you will need to check thoroughly by close comparison - unless anyone else has done the swap? | ||||||||
| | |
| | #4 | |||||||||
![]() Join Date: May 2008 Location: Fleetwood,Lancs Thanks: 0
Thanked 0 Times in 0 Posts
![]()
| Quote:
a little too much enthusiasm I think!Thanks for the info. Cheers, Greg. | |||||||||
| | |
| | #5 | ||||||||
![]() Join Date: Nov 2007 Thanks: 3
Thanked 15 Times in 5 Posts
![]()
| Anything is possible, if you can use a welder then you can make-up new mounting points so that any seat would fit. | ||||||||
| | |
| | #6 | ||||||||
![]() Join Date: May 2008 Location: Lytham St Annes Lancashire Thanks: 0
Thanked 0 Times in 0 Posts
![]()
| Previa 7 and 8 seater floor pans are not the same but as SAVA9E says anything is possible if you can use a welder just watch Pimp my Ride on telly. | ||||||||
| | |
| | #7 | |||||||||
![]() Join Date: May 2008 Location: Texas, USA Thanks: 0
Thanked 0 Times in 0 Posts
![]()
| Quote:
| |||||||||
| | |
| | #8 | ||||||||
![]() Join Date: May 2008 Location: Lytham St Annes Lancashire Thanks: 0
Thanked 0 Times in 0 Posts
![]()
| My TCR 11R 94 Previa has 8 seats and independent suspension the US workshop manual does not cover changing the rear shocks on independent suspension. I have changed mine and its a bit of a B*****d but now ive done it it will be easy next time. | ||||||||
| | |
| | #9 | ||||||||
| Join Date: Dec 2007 Location: northampton Thanks: 0
Thanked 0 Times in 0 Posts
![]()
| to be trueful i think renault got the better idea in my espace i had the front captain seats and all the back seats were seperate and held with floor catches sunken slightly u pull leaver and could remove all seats without any tools and turn into a van.that was on 2.9 v6 rxe not sure about the lower range. | ||||||||
| | |
![]() |
| Tags |
| captains, previa, seats |
| Sponsored Links |
| Thread Tools | |
| Display Modes | |
| |