Captains seats for previa

Greg Ledder · 20th May 2008, 07:58 AM

Hi all!
Does anyone know if it is possible to fit captains seats in place of the driver / front passenger seats in a '94 Previa 2.4 Auto please? If so, which seats would you recommend? I know that access to the engine has to be retained and this could make things a bit awkward.
Also,can the middle bench seat be replace with swivelling seats and would seats from a Lucida/Emina fit?
I'm wanting to use the bus as an occasional weekend camper and the swivelling seats would be a big help. I'm planning to remove the rear seats in favour of a removeable hob/grill/sink unit.
If anyone has done a similar conversion I would love to hear from you - any help / ideas would be greatly appreciated.
Many thanks,
Greg.

TheMAN · 20th May 2008, 08:02 AM

Quote:

Originally Posted by Greg Ledder

Hi all!
Does anyone know if it is possible to fit captains seats in place of the driver / front passenger seats in a '94 Previa 2.4 Auto please? If so, which seats would you recommend? I know that access to the engine has to be retained and this could make things a bit awkward.
Also,can the middle bench seat be replace with swivelling seats and would seats from a Lucida/Emina fit?
I'm wanting to use the bus as an occasional weekend camper and the swivelling seats would be a big help. I'm planning to remove the rear seats in favour of a removeable hob/grill/sink unit.
If anyone has done a similar conversion I would love to hear from you - any help / ideas would be greatly appreciated.
Many thanks,
Greg.

unless you're a midget, installing captain seats in the front is not going to be really possible

as for the middle row, I'm sure the floorpan is the same on all of the previas, it's just the seat retaining hooks will obviously be different as well as holes in the carpet... I would pull back the carpet to make sure before attempting the swap though

Ian · 20th May 2008, 08:13 AM

I don't know about the Previa - but I do know that the Estima has a different floor pan between the 7 and 8 seater ( different rear axle setup as well) and the middle row seats are not interchangeable.
Seems the 7 seater is the higher spec and a different floor pan is required for the independent rear axle and captains seats.

So you will need to check thoroughly by close comparison - unless anyone else has done the swap?

Greg Ledder · 20th May 2008, 08:17 AM

Quote:

Originally Posted by TheMAN

unless you're a midget, installing captain seats in the front is not going to be really possible

as for the middle row, I'm sure the floorpan is the same on all of the previas, it's just the seat retaining hooks will obviously be different as well as holes in the carpet... I would pull back the carpet to make sure before attempting the swap though

Good point about the front seats - didn't really think that one through.......

a little too much enthusiasm I think!
Thanks for the info.
Cheers,
Greg.

SAVA9E · 20th May 2008, 08:37 AM

Anything is possible, if you can use a welder then you can make-up new mounting points so that any seat would fit.

LeeBee · 20th May 2008, 01:25 PM

Previa 7 and 8 seater floor pans are not the same but as SAVA9E says anything is possible if you can use a welder just watch Pimp my Ride on telly.

TheMAN · 20th May 2008, 01:47 PM

Quote:

Originally Posted by Ian

I don't know about the Previa - but I do know that the Estima has a different floor pan between the 7 and 8 seater ( different rear axle setup as well) and the middle row seats are not interchangeable.
Seems the 7 seater is the higher spec and a different floor pan is required for the independent rear axle and captains seats.

So you will need to check thoroughly by close comparison - unless anyone else has done the swap?

ok, but the US never got the 8 seater, yet have the 8 seater rear axle setup... talk about strange! I guess toyota decided they needed reliability for heavy loads and abuse americans would put through on the vehicle! in otherwords, all US previas have the solid rear axle

LeeBee · 20th May 2008, 01:56 PM

My TCR 11R 94 Previa has 8 seats and independent suspension the US workshop manual does not cover changing the rear shocks on independent suspension. I have changed mine and its a bit of a B*****d but now ive done it it will be easy next time.

davemina · 27th May 2008, 11:52 PM

to be trueful i think renault got the better idea in my espace i had the front captain seats and all the back seats were seperate and held with floor catches sunken slightly u pull leaver and could remove all seats without any tools and turn into a van.that was on 2.9 v6 rxe not sure about the lower range.

20th May 2008, 07:58 AM	#1 (permalink)
Greg Ledder Join Date: May 2008 Location: Fleetwood,Lancs Posts: 29	Captains seats for previa Hi all! Does anyone know if it is possible to fit captains seats in place of the driver / front passenger seats in a '94 Previa 2.4 Auto please? If so, which seats would you recommend? I know that access to the engine has to be retained and this could make things a bit awkward. Also,can the middle bench seat be replace with swivelling seats and would seats from a Lucida/Emina fit? I'm wanting to use the bus as an occasional weekend camper and the swivelling seats would be a big help. I'm planning to remove the rear seats in favour of a removeable hob/grill/sink unit. If anyone has done a similar conversion I would love to hear from you - any help / ideas would be greatly appreciated. Many thanks, Greg.

20th May 2008, 08:13 AM	#3 (permalink)
Ian Join Date: Dec 2007 Posts: 379	I don't know about the Previa - but I do know that the Estima has a different floor pan between the 7 and 8 seater ( different rear axle setup as well) and the middle row seats are not interchangeable. Seems the 7 seater is the higher spec and a different floor pan is required for the independent rear axle and captains seats. So you will need to check thoroughly by close comparison - unless anyone else has done the swap? __________________

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

20th May 2008, 08:37 AM	#5 (permalink)
SAVA9E Join Date: Nov 2007 Location: WORCESTER Posts: 2,878	Anything is possible, if you can use a welder then you can make-up new mounting points so that any seat would fit.

20th May 2008, 01:25 PM	#6 (permalink)
LeeBee Join Date: May 2008 Location: Lytham St Annes Lancashire Posts: 12	Previa 7 and 8 seater floor pans are not the same but as SAVA9E says anything is possible if you can use a welder just watch Pimp my Ride on telly.

20th May 2008, 01:56 PM	#8 (permalink)
LeeBee Join Date: May 2008 Location: Lytham St Annes Lancashire Posts: 12	My TCR 11R 94 Previa has 8 seats and independent suspension the US workshop manual does not cover changing the rear shocks on independent suspension. I have changed mine and its a bit of a B*****d but now ive done it it will be easy next time.

27th May 2008, 11:52 PM	#9 (permalink)
davemina Join Date: Dec 2007 Location: northampton Posts: 178	to be trueful i think renault got the better idea in my espace i had the front captain seats and all the back seats were seperate and held with floor catches sunken slightly u pull leaver and could remove all seats without any tools and turn into a van.that was on 2.9 v6 rxe not sure about the lower range.